FOX Corporation requires the safe use of powered hand tools in all its work activities, in accordance with the requirements in this Procedure.

1.0 SCOPE

FOX Corporation (FOX) is committed to the safe use of all powered hand tools in support of Productions and Operations. This Procedure addresses
requirements for use of these devices.

2.0 Definitions

None.

3.0 Responsibilities

In addition to required Environmental, Health and Safety (EHS) Program responsibilities discussed in EHS001, EHS Policy, the responsibilities described
below are necessary to ensure the effectiveness of the procedure.

3.1 Department Heads

Department Heads will ensure that their personnel are aware of these requirements.

3.2 Employees

All FOX employees will observe the requirements specified in this Procedure for the use of powered hand tools.

3.3 Environmental, Health and Safety Department

The EHS Department will:

Develop appropriate standards for the use of powered hand tools in all FOX activities
Review and update this Procedure annually, or as necessary, to comply with regulatory changes.

4.0 Procedure

These requirements pertain to powered hand tools used in all work settings.

4.1 General Requirements

4.1.1 Selection and Use

Always wear safety glasses or goggles [and also a faceshield, if the impact hazard is high (see EHS 301, Personal Protective Equipment)].
Wear hearing protection that is suitable for the level and frequency of the noise you are exposed to in the working area (see EHS 203, Hearing Conservation Program).
Make sure all machine guards are in position, are in good working condition, and guard the machine adequately before operating any equipment or machine
(see EHS 407, Machine Guarding). Check and adjust all other safety devices.
Turn the power OFF and unplug the power cord (or lock out the power source) before inspecting, changing, cleaning, adjusting, or repairing a blade or a
machine (see EHS 403, Lockout/Tagout). Also, turn the power OFF when discussing the work.
Select tools that can be used without bending the wrist. Hand tools should be designed to allow the operator to grasp, hold, and use the tool with the
wrist held straight.
Select the tool with the workplace layout and job design in mind. Sometimes a tool is correct for one operation and incorrect for another.
Use the right tool for the job.

· Ensure it is the right size and has sufficient power to do the job safely.

· When a choice is presented, select the tool of the lesser weight.

Select low-vibrating tools, or choose tools with vibration-absorbing handles, like those covered with cork, rubber, plastic, or plastic bonded to
steel, to reduce hand-arm vibration.
Choose hand tools that have the center of gravity within, or close to, the handle.
Select tools with rounded and smooth handles that you can grip easily.
If they are available, choose hand tools with double handles to permit easier holding and better manipulation of the tool.
Select tools with a trigger strip, rather than a trigger button. This strip will allow you to exert more force over a greater area of the hand that, in
turn, will reduce muscle fatigue.
Ensure that the trigger works easily to reduce the effort needed to operate it.
Ensure that your tool is well maintained and in good repair.
Frequently used tools that weigh more than one (1) pound should be counter-balanced.
Hold the tool close to the body. Do not overreach.
Keep good balance and proper footing at all times. This will help operators to control the tool better, especially in response to unexpected
situations.
Rest your hands by putting the tool down when you are not using it.
Reduce power to the lowest setting that can complete the job safely. This action reduces tool vibration at the source.
Ensure that cutting tools, drill bits, etc. are kept sharp, clean and well maintained.
Do not wear gloves, loose clothing, or jewelry while using revolving power tools.
Tie back long hair or wear appropriate hair protection to prevent hair from becoming entangled in moving parts of equipment.
Do not use a tool, unless you have been trained to use it safely, and know its limitations and hazards.

4.1.2 Storage and Handling

All tools must be stored in a manner to prevent damage and injury. Store tools in a dry, secure location when they are not in use.
Tools must be properly stored after use.
When transporting tools, sharp/pointed edges must be:

Covered

· Carried in a toolbox or other device designed for that purpose, or

Pointed downward, away from the body.

4.2 Electric Tools

4.2.1 General Requirements

All electrical tools and equipment must be operated in accordance with the requirements of EHS 410, Portable Electrical Equipment.

4.2.1.1 Inspection

Inspect tools for any damage prior to each use.
Ensure that the power tool has the correct guard, shield, or other attachment that the manufacturer recommends.

3. Ensure that the tools are:

· Properly grounded, using a three (3)-prong plug

· Double-insulated (and are labeled as such), or

· Powered by a low-voltage isolation transformer. This will protect users from an electrical shock.

Check electric tools to ensure that a tool with a three (3)-prong plug has an approved three (3)-wire cord and is grounded.

· The three (3)-prong plug must be plugged into a properly grounded three (3)-pole outlet.

· If an adapter must be used to accommodate a two (2)-hole receptacle, the adapter wire must be attached to a known, functioning ground.

· Never remove the third grounding prong from a plug.

Check the handle and body casing of the tool for cracks or other damage.
If the tool has auxiliary or double handles, check to see that they are installed securely.
Inspect cords for defects: check the power cord for cracking, fraying, and other signs of wear or faults in the cord insulation.
Check for damaged switches and faulty trigger locks.
Inspect the plug for cracks and for missing, loose, or faulty prongs.
If a tool is defective, remove it from service, and tag it clearly “Out of service for repair.”

· Replace damaged equipment immediately.

· Do not use defective tools “temporarily.”

Do not attempt field repairs.

4.2.1.2 Battery-Powered Tools

1. Use only the kind of battery that the tool manufacturer specifies for the battery-powered tool that you are using.

Recharge a battery-powered tool only with a charger that is specifically intended for the battery in that tool.

3. Remove the battery from the tool, or ensure that the tool is switched OFF or locked off before changing accessories, making adjustments, or storing the
tool.

Store a battery pack safely so that no metal parts, nails, screws, wrenches, etc., can come in contact with the battery terminals

This could result in shorting the battery, and possibly causing sparks, fires, or burns.

4.2.1.3 Using Electric Tools

Switch OFF the tools before connecting them to a power supply.
If a power cord feels more than comfortably warm, or if a tool is sparking excessively, have it checked by an electrician or other qualified person.
Disconnect the power supply before making adjustments or changing accessories.
Remove any wrenches and adjusting tools before turning on a tool.
Inspect the cord for fraying or damage before each use. Tag defective tools clearly with an “Out of Service” tag and replace immediately with a tool in
good running order.

6. During use, keep power cords clear of tools and the path in which the tool will be directed.

Use clamps, vices, or other devices to hold and support the piece being worked on, when practical to do so. This will allow you to use both hands for
better control of the tool and will help prevent injuries, if a tool jams or binds in a work piece.
Use only approved extension cords that have the proper wire size for the length of cord and power requirements of the electric tool that you are using.

This will prevent the cord from overheating.

For outdoor work, use outdoor extension cords marked “W-A” or “W.”
Suspend power cords over aisles or work areas to eliminate stumbling or tripping hazards.
Eliminate octopus connections. If more than one receptacle plug is needed, use a power bar or power distribution strip that has an integral power cord
and a built-in overcurrent protection.
Do not disconnect the power supply of the tool by pulling or jerking the cord from the outlet.
Keep power cords away from heat, water, oil, sharp edges, and moving parts.

They can damage the insulation and cause a shock.

Avoid accidental starting by ensuring the tool is turned OFF before you plug it in. Also, do not allow your finger to touch the switch when walking
with a plugged-in tool.
Do not bypass the ON/OFF switch and operate the tools by connecting and disconnecting the power cord.
Pull the plug, not the cord, when unplugging a tool. Pulling the cord causes wear and might adversely affect the wiring to the plug, and an electrical
shock to the operator might occur.
Do not leave a running tool unattended. Do not leave it until it has been turned OFF, has stopped running completely, and has been unplugged.
Do not use electric tools in wet conditions or damp locations, unless tool is connected to a ground fault circuit interrupter (GFCI).
Do not expose electric power tools to rain or wet conditions; wet tools increase the likelihood for incurring an electrical shock.
Avoid body contact with grounded surfaces, like refrigerators, pipes, and radiators, when using electric powered tools, this will reduce the likelihood
of shock if the operator’s body is grounded.
Do not plug several power cords into one outlet by using single-to-multiple outlet adapters or converters (“cube taps”).
Do not use light duty power cords.
Do not connect or splice extension cords together to make a longer connection, the resulting extension cord might not be able to provide sufficient
current or power safely.
Do not carry electrical tools by the power cord.
Do not tie power cords in knots, which can cause short circuits and shocks. Loop the cords or use a twist lock plug.
Never break off the third prong on a plug. Replace broken three (3)-prong plugs and make sure the third prong is properly grounded.
Never use extension cords as permanent wiring. Use extension cords only as a temporary power supply to an area that does not have a power outlet.
Do not walk on or allow vehicles or other moving equipment to pass over unprotected power cords. Cords should be put in conduits or protected by
placing planks on each side of them.
Do not bush away sawdust, shavings, or turnings while the tool is running. Never use compressed air for cleaning surfaces or removing sawdust, metal
turnings, etc.
Do not operate tools in an area containing explosive vapors or gases.
Do not clean tools with flammable or toxic solvents.
Do not surprise or touch anyone who is operating a tool. Startling a tool operator could result in causing an accident or injury.

4.2.2 Belt Sanders

Wear safety glasses.
Make sure the sander is switched “OFF” before connecting the power supply.
Disconnect power supply before changing a sanding belt, making adjustments, or emptying dust collector.
Inspect sanding belts before using them.
Replace those belts that are worn or frayed.

6. Install sanding belts that are the same widths as the pulley drum.

Adjust sanding belt tension to keep the belt running true and at the same speed as pulley drum.
Secure the sanding belt in the direction shown on the belt and the machine.
Keep hands away from a sanding belt.
Use two hands to operate sanders; one on the trigger switch and the other on the front handle knob.
Keep all cords clear of sanding area during use.
Clean dust from a motor and vents at regular intervals.

13. Do not use a sander without an exhaust system or a dust collector present that is in good working order. The dust created when sanding can be a fire
and explosion hazard.

· Empty the collector when one-fourth (1/4) full.

· Proper ventilation is essential.

Do not exert excessive pressure on a moving sander. The weight of the sander supplies adequate pressure for the job.

15. Do not work on unsecured stock unless it is heavy enough to stay in place.

· Clamp the stock into place, or

· Use a “stop block” to prevent movement.

Do not overreach. Always keep proper footing and balance.
Do not cover the air vents of the sander.

4.2.3 Drills

Wear safety glasses.
Keep drill air vents clear to maintain adequate ventilation.
Always keep drill bits sharp.
Keep all cords clear of the cutting area during use. Inspect for frays or damage before each use.
Disconnect power supply before changing or adjusting bit or attachments.
Tighten the chuck securely.
Remove chuck key before starting drill.
Secure workpiece being drilled to prevent movement.
Slow the rate of feed just before breaking through the surface.
Drill a small “pilot” hole before drilling large holes.
For small pieces, clamp stock so work will not twist or spin. Do not drill with one hand while holding the material with the other.
Do not use a bent drill bit.
Do not exceed the manufacturer’s recommended maximum drilling capacities.
Do not use a hole saw cutter without the pilot drill.
Do not use high-speed steel (HSS) bits without cooling or using lubrication.

16. Do not attempt to free a jammed bit by starting and stopping the drill.

· Unplug the drill.

· Remove the bit from the workpiece.

Do not reach under or around stock being drilled.
Do not overreach. Always keep proper footing and balance.
Do not raise or lower the drill by its power cord.

4.2.4 Planers

Wear safety glasses.
Disconnect the planer from the power supply before making any adjustments to the cutter head or blades.
Use blades of the same weight and set at the same height.
Ensure that the blade-locking screws are tight.
Remove adjusting keys and wrenches before turning on power.
Support the material (stock) in a comfortable position that will allow the job to be performed safely and accurately.
Check stock thoroughly for staples, nails, screws, or other foreign objects before using a planer.
Start a cut with the infeed table (front shoe) resting firmly on the stock and with the cutter head slightly behind the edge of the stock.
Use two hands to operate a planer; one hand on the trigger switch and the other on a front handle.
Do not put your finger or any object in a deflector to clean out chips while a planer is running.
Disconnect the power supply when stopping to remove chips.
Do not set a planer down until blades have stopped turning.
Keep all cords clear of cutting area.

4.2.5 Routers

Wear safety glasses.
Disconnect the power supply before making any adjustments or changing bits.
Ensure that the bit is securely mounted in the chuck and the base is tight.
Place the base of the router on the work, template, or guide.
Make sure that the bit can rotate freely before switching on the motor.

6. Secure stock.

· Never rely on yourself or a second person to support or hold the material.

· Sudden torque or kickback from the router can cause damage and injury.

Before using a router, check stock thoroughly for staples, nails, screws, or other foreign objects.
Keep all cords clear of cutting area.
Always hold router handles with both hands until a motor has stopped.
Do not set the router down until exposed router bit has stopped turning.
Do not overreach.
Keep proper footing and balance.
When performing inside routing, start the motor with the bit above the stock. When the router reaches full power, lower bit to required depth.
When routing outside edges, guide the router counter clockwise around the work.
When routing bevels, moldings, and other edge work, make sure the router bit is in contact with the stock to the left of a starting point and is
pointed in the correct cutting direction.
Feed the router bit into the material at a firm, controlled speed.
With softwood, you can sometimes move the router as fast as it can go.

With hardwood, knotty and twisted wood, or with larger bits, cutting might be very slow.

The sound of the motor can indicate safe cutting speeds.

· When the router is fed into the material too slowly, the motor makes a high-pitched whine.

· When the router is pushed too hard, the motor makes a low growling noise.

When the type of wood or size of the bit requires going slowly, make two or more passes to prevent the router from burning out or kicking back.
To decide the depth of cut and how many passes to make, test the router on scrap lumber similar to the wood being used.

4.2.6 Circular Saws

Wear safety glasses and hearing protection.
Check the retracting lower blade guard to make certain it works freely.
Ensure that the blade that you have selected is sharp enough to do the job. Sharp blades work better and are safer.
Check the saw for proper blade rotation.
Set the depth of the blade, while the saw is unplugged, and lock it at a depth so that the lowest tooth does not extend more than about one-eighth
(1/8) inch beneath the wood.
Keep all cords clear of cutting area.
Circular saws are designed for right-hand operation; left-handed operation will demand more care to operate safely.

8. Check the retracting lower blade guard frequently to make certain it works freely.

It should:

· Enclose the teeth as completely as possible, and

· Cover the unused portion of the blade when cutting.

Check that the retracting lower blade guard has returned to its starting position before laying down the saw.
Keep upper and retracting lower blade guard clean and free of sawdust.
Disconnect power supply before adjusting or changing the blade.
Allow the saw to reach full power before starting to cut.
Use two hands to operate saws; one on a trigger switch and the other on a front knob handle.
Keep the motor free from accumulation of dust and chips.
Select the correct blade for stock being cut and allow it to cut steadily. Do not force it.
Secure work being cut to avoid movement.
Do not hold or force the retracting lower guard in the open position.
Do not place hand under the shoe or guard of the saw.
Do not over-tighten the blade-locking nut.
Do not twist the saw to change, cut, or check alignment.
Do not use a saw that vibrates or appears unsafe in any way.
Do not force the saw during cutting.
Do not cut materials without first checking for obstructions or other objects, such as nails and screws.
Do not carry the saw with a finger on the trigger switch.
Do not overreach. Keep proper footing and balance.
Do not rip stock without using a wedge or guide, clamped or nailed to the stock.

4.2.7 Other Saws

Wear safety glasses.
Disconnect power supply before changing or adjusting blades.
Use lubricants when cutting metals.
Keep all cords clear of cutting area.
Position the saw beside the material before cutting and avoid entering the cut with a moving blade.
Make sure guards, if present, are installed and are working properly.
Remember sabre saws cut on the up stroke.
Secure and support stock as close as possible to the cutting line to avoid vibration.
Keep the base or shoe of the saw in firm contact with the stock being cut.

10. Select the correct blade for the material being cut and allow it to cut steadily.

· Do not force it.

· Clean and sharp blades operate best.

Set the blade to extend no further than one-eighth (1/8) to one-fourth (1/4) inch deeper than the material being cut.
Do not start cutting until the saw reaches its full power.
Do not force a saw along or around a curve. Allow the machine to turn with ease.
Do not insert a blade into or withdraw a blade from a cut or lead hole while the blade is moving.
Do not put down a saw until the motor has stopped.

16. Do not reach under or around the stock being cut.

Maintain control of the saw always. Avoid cutting above shoulder height.

18. External Cuts:

a. Make sure that the blade is not in contact with the material or the saw will stall when the motor starts.

b. Hold the saw firmly down against the material and switch the saw on.

c. Feed the blade slowly into the stock, maintaining an even forward pressure.

19. Internal Cuts:

a. Drill a lead hole slightly larger than the saw blade.

b. With the saw switched OFF, insert the blade in the hole until the shoe rests firmly on the stock.

c. Do not let the blade touch the stock until the saw has been switched on.

4.3 Pneumatic Tools

4.3.1 General Requirements

1. Wear safety glasses.

Ensure that the compressed air supplied to the tool is clean and dry.

· Dust, moisture, and corrosive fumes can damage a tool.

· An in-line regulator filter and lubricator increases tool life.

Keep tools clean and lubricated, and maintain them according to the manufacturers’ instructions.
Use only the attachments that the manufacturer recommends for the tools you are using.
Be careful to prevent hands, feet, or body from injury in case the machine slips, or the tool breaks.
Reduce physical fatigue by supporting heavy tools with a counter-balance wherever possible.
Use the proper hose and fittings of the correct diameter.

8. Use hoses specifically designed to resist abrasion, cutting, crushing, and failure from continuous flexing.

Choose air-supply hoses that have a minimum working pressure rating of one hundred fifty (150) psig or one hundred fifty (150) percent (%) of the
maximum pressure produced in the system, whichever is higher.
Check hoses regularly for cuts, bulges, and abrasions. Tag and replace, if defective.
Blow out the airline before connecting a tool. Hold hose firmly and blow away from yourself and others.
Make sure that hose connections fit properly and are equipped with a mechanical means of securing the connection (e.g., chain, wire, or positive
locking device).
Install quick disconnects of a pressure-release type, rather than a disengagement type. Attach the male end of the connector to the tool, NOT to the
hose.
Do not operate the tool at a pressure above the manufacturer’s rating.
Turn OFF the air pressure to hose when not in use or when changing power tools.
Do not carry a pneumatic tool by its hose.
Avoid creating trip hazards caused by hoses across walkways or curled underfoot.
Do not use compressed air to blow debris or to clean dirt from clothes.

4.3.2 Pneumatic Nailing and Stapling Tools

Permit only experienced and trained persons to operate pneumatic nailing and stapling tools.
Wear safety glasses or a face shield and, where necessary, use hearing protection.

3. Inspect a tool before connecting it to air supply:

a. Check tool safety mechanisms, if applicable.

b. Tighten securely all screws and cylinder caps.

Check correct air supply and pressure before connecting a tool.
Check that the tool is correctly and securely connected to the air supply hose and that it is in good working order, with the safety mechanism
operative, before using.
Always handle a tool as though it is loaded with fasteners (nails, staples, etc.).
Equip tools with a work-contacting element that limits the contact area to one that is as small as practical.
Make sure that the mechanical linkage between the work-contacting element and trigger is enclosed.
Disconnect a tool from the air supply when the tool is unattended, and during cleaning or adjustment. Before clearing a blockage, be sure that
depressing the trigger exhausts all air from the tool.
Use only fasteners recommended by the manufacturer.
Permit only properly trained people to carry out tool maintenance.
Do not operate at a pressure above the manufacturers’ rating.
Do not depress the trigger, unless the nosepiece of the tool is directed onto a safe work surface.
Do not carry a tool with the trigger depressed.
Do not load a tool with fasteners while the trigger is depressed.
Do not overreach. Keep proper footing and balance.
Do not use compressed air to blow debris or to clean dirt from clothes.

4.4 Powder-Actuated Tools

Only powder-actuated tools, meeting the design requirements of ANSI A10.3-1977, “Safety Requirements for Powder-Actuated Fastening Systems,” may be used.

The powder-actuated tool must be kept in a locked container. Only qualified operators may have keys to the storage container for powder-actuated tools. The
storage container must be labeled “POWDER-ACTUATED TOOL,” and the following warning must be attached to the inside cover of the container:

WARNING – POWDER-ACTUATED TOOLS ARE TO BE USED ONLY BY A QUALIFIED OPERATOR AND TO BE KEPT UNDER LOCK AND KEY WHEN NOT IN USE

4.4.1 Operational Requirements

1. Each tool must be supplied with the following:

Operator’s instruction and service manual
Powder load and fastener chart
Tool inspection and service record

· Service tools and accessories; only approved pole tool assemblies will be used.

The tool must be serviced and inspected for worn or damaged parts at regular intervals as recommended by the tool manufacturer.

· Before the tool is returned to service, a qualified person must replace all worn or damaged parts with manufacturer’s approved parts.

· A record of this inspection and service must be noted and dated on the tool inspection record.

The instruction manuals, maintenance tools, and accessories supplied with the tool, must be stored in the tool container when not in use.
Powder-actuated tools must not be used in an explosive or flammable atmosphere.
A loaded tool must never be left unattended.
Fasteners must not be driven into very hard or brittle materials, including, but not limited to, cast iron, glazed tile, hardened steel, glass block,
natural rock, hollow tile, or most brick.
Fasteners must not be driven into easily penetrated or thin materials, or materials of questionable resistance, unless backed by a material that will
prevent the fastener from passing completely through the other side.
Fasteners must not be driven closer than three (3) inches (76 mm) from the unsupported edge of masonry materials, except for specific applications
recommended by the tool manufacturer.
Fasteners must not be driven into concrete, unless the material thickness is at least three (3) times the fastener shank penetration.
Fasteners must not be driven into any spalled area.
Fasteners must not be driven through existing holes, unless a specific guide means, as recommended by the tool manufacturer, is used to assure positive
alignment.
The operator and all assistants must wear eye/face protection, and earplugs or muffs, when the tool is in use.
The operator must inspect the tool to determine that it is in proper working condition, in accordance with the testing methods recommended by the tool
manufacturer, before using the tool.
Any tool that is found not to be in working condition must be immediately removed from service, tagged “defective,” and not used until it has been
repaired, in accordance with the manufacturer’s instructions.
The shield, fixture, adapter, or accessory suited for the application, as recommended and supplied by the manufacturer, must be used.
Only those fasteners and powder loads recommended by the tool manufacturer for a particular tool, or those providing the same level of safety and
performance, will be used.
Tools must not be loaded until just prior to the intended firing time.
If the work is interrupted after loading, then the tool must be unloaded immediately.
Neither loaded nor empty tools will be pointed at any person.
Hands and feet must be kept clear of the open barrel end.
The tool always must be held perpendicular to the work surface when fastening into any material, except for specific applications recommended by the
tool manufacturer.
In the event of a misfire, the operator must hold the tool firmly against the work surface for a period of not less than fifteen (15) seconds, and then
follow the instructions set forth in the manufacturer’s instructions.
Powder loads, of different powder levels and types, must be kept in separate compartments or containers.
Cased powder loads must be coded to identify powder load levels by case color and powder load color.
Caseless powder loads must be coded to identify powder load levels by color and configuration.
No powder load, cased or caseless, will be used if it will properly chamber in any existing commercially available tool and will cause a fastener to
have a test velocity in excess of the maximum test velocity specified for that tool.
Powder load packages must provide a visual number-color indication of the powder level of the load.

4.4.2 TRAINING

Before employees are permitted to use powder-actuated tools, they must have been thoroughly instructed by a competent person in the following:

1. Before using a tool, inspect it to determine that it is clean, that all moving parts operate freely and that the barrel is free from obstructions.

2. When a tool develops a defect during use, immediately cease to use it and notify the supervisor.

3. Tools must not be loaded until just prior to the intended firing time, and the tool must not be left unattended while loaded.

4. The tool, whether loaded or empty, must not be pointed at any person, and hands shall be kept clear of the open barrel end.

5. In case of a misfire, hold the tool in the operating position for at least fifteen (15) seconds, and continue to hold the muzzle against the work
surface, during disassembly or opening the tool for removal of the powder load.

6. Neither tools nor powder charges will be left unattended in places where they would be available to unauthorized persons.

5.0 REFERENCES

EHS 001, EHS Policy

EHS 204, Hearing Conservation Program

EHS 301, Personnel Protective Equipment

EHS 403, Lockout/Tagout

EHS 407, Machine Guarding

EHS 409, Portable Electrical Equipment

EHS 506, Hearing Conservation Program

6.0 ATTACHMENTS

None.